Manual
PAGE-1
Description
|
Input Voltage
|
DC+12V
|
|
Standby
|
Display shows:00:00, rely: Normal Open (NO)
|
|
Accumulated time
|
Yes, add time if receive signals again when time is running
|
|
Max current load
|
15A
|
|
How it works
|
|
Mode 1
|
Time runs down after receive signals-> Display shows remaining time and supply power to device-> it cuts off power after time runs out
|
|
Mode 2
(Connect a button)
|
Display shows remaining time after receive signals-> push button start-> time runs down and supply power to device-> it cuts off power after time runs out
|
|
Pause
(connect a button)
|
Push button pause: it cuts off power when pause, display shows remaining time. Re-supply power after push button pause again
|
|
Operating Mode
|
Please reference to page 2
|
|
Connection Example
|
Please reference to page 2
|
Connection and Position
|
1: Display 2: 40 cm white lead
3: Switch control device power wire:
control “L” or “N” of device power wire
4: AC jack-5.5mm*2.1mm
5: YELLOW: DC12V, WHITE: input signal, BLACK: GND
6: START for mode 01:02 7: Pause
8-11: Button S2, S1, S3, and S4
|
|
|
Max Time:99:59 Display: 99:59
A: 2 digit: either HOUR or MINUTE
B: 2 digits: either MINUTE or SECOND
Please following page to adjust Time type.
|
|
Setting
Please follow CODE ON DISPLAY and use button "S1" and "S2" to set up number
- INPUT SIGNAL QUANTITY AND TIME
- Please press button "S4". “B” flashes. Please set up INPUT SIGNAL QUANTITY to active device (01-50).
- Please press button "S4", “A” flashes. Please set up TIME (01-99).
- Please press button "S4", “B” flashes. Please set up TIME (01-99).
- Please press button “S4” 4 TIMES.
- Please set up TIME for Warning Sound.
- Please press button "S4" to finish.
PAGE-2
- GIVEN TIME: Add time by free if input signals reach SETTING RATE during time is running.
Example Setting: input signal to active device: 01, input signals for given time: 03 give time: 02:10
Add time “02:10” free if receive “3 signals” during time is running.
- Please press button "S4" 4 TIMES. “B” flashes. Please set up RATE OF INPUT SIGNAL QUANTITY.
- Please press button "S4", “A” flashes. Please set up GIVEN TIME.
- Please press button "S4", “B” flashes. Please set up GIVEN TIME.
- Please press button "S4" to finish.
Please follow table to set up operating function:
- Please hold on button "S1" and "S2" simultaneously for 3 seconds to get into MODE SETTING.
- Please use button "S1" and button "S2" to set up number for CODE
- Please press button "S4" to switch to next code
|
Function
|
Code on Display
|
Description
|
|
A
|
B
|
|
Running Time
|
01
|
01
|
Time runs down without pressing button
|
|
02
|
Time runs down by pressing button
|
|
Time Type
|
02
|
03
|
MINUTE: SECOND
|
|
04
|
HOUR: MINUTE
|
|
Memory
|
03
|
05
|
Yes: Remaining time keep running after power off and on
|
|
06
|
No: Standby power off and on
|
|
Back to standby
|
04
|
1-30
|
user has no action after push buttons or receive signals in setting time
|
|
Default: 01-03: Bold and base line. 04: not use the function.
|
Connection Example
comparison
Main board
Display
USD
EUR
GBP
CAD
CNY
SAR
SGD
NZD
ARS
INR
COP
AED
